“Start to Finish” Part III
 

Obsolete Outboards
by Max Wawrzyniak


“Start to Finish”
Part III

Sierra Marine is the company that sells after-market replacement parts for marine engines. One of the types of items that they sell is carburetor rebuild kits. I have used many of their kits with few problems, and one nice thing that many of their kits contain is a set of instructions with drawings. I purchased a Sierra kit for the Johnson

Taking the carb apart is no big deal (neither is putting it back together.) Unscrew the high and low speed needles along with their packing nuts, then remove the 5 or so screws which hold the bowl on. Once the bottom of the bowl is removed, the cork float can be removed by pushing out it’s hinge pin. Don’t allow carb cleaner to get on the cork float, as the float is varnished, and carb cleaner removes varnish. Most OMC carbs will also have a brass “nozzle” running up vertically through the center of the carb’s upper half. Remove and blow it out with the spray carb cleaner, and take note of the “doughnut” seal (usually cork) which sits on the nozzle.

You will need a very-wide blade screwdriver to remove the float valve seat from the upper half of the carb. If you strip it’s little slots with the wrong size screwdriver, getting the old seat out may be a chore. You might want to invest in a good screwdriver of the proper size for this chore. Note the seal under the seat.

At this point, the carb is “tore down” as much as I usually dissasemble it.

The kit will probably contain some tiny welch plugs (like small freeze plugs) and the instructions may say to remove the old welch plugs from the body of the carb in order to clean the passages behind them. Installing the new welch plugs can be a big hassle and I almost never remove the old ones if they are showing no signs of leakage.

Your can of spray carb cleaner should have come with a tiny plastic tube for spraying into tight places. Put on your safety goggles and install the tube in the can’s nozzle and find a place where dripping flammable cleaner will not be a hazard. Spray the cleaner into each and every opening and passage on the carb. Keep in mind that as you shoot cleaner into one passage, it may come shooting out of another passage aimed directly at your face. Keep cleaning until you think your have gotten rid of any crud and the passages appear clean.

In the “old days,” it was usually recommended that one soak the carb in a container of carb cleaner. I used to do that, but for the last few years I have just sprayed them out with the spray cleaner and have had no problems.

Note; there is “packing” in the openings that the high and low speed needles screw into. The packing nuts (threaded tubes) that install over the needles tighten down on tiny rings of a sealant material in order to prevent leakage around the needles. As new packing is supplied in the kit, the best thing to do is remove the old packing prior to cleaning. That can be easier said than done, and I usually just leave the old stuff in there, and add a new ring or two of packing on top when reinstalling the needles and packing nuts. Be mindful that if the old packing becomes dislodged and stuck in the needle’s seat, your engine will not run correctly.


After the carb appears clean, install the new needle seat and seal, and reinstall that brass vertical nozzle and it’s new “doughnut” seal. You can install the new bowl needle along with the old float (assuming the old float is not in too bad of condition, and most that I see are not). Note that the kit usually contains a tiny wire “hair pin” that connects the float needle to the float arm, so that the needle is pulled open by the weight of the float and not just by it’s own weight.

You can now install the bottom of the bowl back onto the carb body, using the new gasket from the kit. Place a new ring or two of packing in the openings for the high and low speed needles and install the needles themselves. Your manual will tell you how many turns from closed the needles need to be set at when trying to start the engine but I never look. I usually try around ¾ to 1 turn open on both needles and play it by “ear.” when trying to start the engine. Install the packing nuts but keep in mind that you may need to remove one or both to get the carb air silencer back on.

Bolt the carb back on the engine using a new gasket; note that these carb kits fit several different engines and you may have a choice of 2 or 3 gaskets - choose the one that matches-up to your old gasket.

After bolting the Johnson’s carb back on, I cut and fitted new fuel hoses and hose clamps. I also installed a small “in-line” fuel filter in the hose. This engine has a fuel strainer/filter bowl on the carb; other OMC’s have a remote-mounted strainer/filter bowl somewhere on the power head. Be sure to clean the strainer element and bowl, and the carb kit should contain a new gasket for the bowl. I like to add the in-line filter as a “belt and suspenders” approach to protecting my newly-rebuilt carb.

With the carb back on the engine and all “hooked-up,” I reinstalled the magneto. As I set it down on it’s mount, I was careful to avoid bending the rubbing block arms of the points on their cam; the arms on the points are spring-loaded and one has to manually pull them back or they will hang up on the cam that actuates them, when installing the magneto. Run the spark plug wires to the back of the engine. Make sure the big sheet metal “cam” that most of these engines use to operate the carb butterfly linkage is in the front of the engine and not “hung-up” on anything. Once you are sure the magneto is correctly in place, put in the four screws which hold it in place and reconnect the linkage arm to the vertical shaft that comes up from the twist-grip throttle control.


Next, I checked and set the carb-to-magneto sychronization, which is not as complicated as it sounds. A manual, such as the one that I reviewed for Duckworks, will show you how to do this, but on old OMC’s all that is involved is lining up the carb linkage with certain marks on the engine.


At this point, you can manually rotate the crankshaft until the keyway is aligned with the rubbing block on one set of points and set the gap on that set to .020. Then rotate the crankshaft until the rubbing block on the other set of points is aligned with the key way and adjust that set of points to .020. Setting the point gap on the Johnson took all of about 5 minutes.


Set the flywheel down on the crankshaft, making sure the key is properly seated. At this point, you can clamp a spark plug to a good ground on the engine with a pair of Vice Grips, and by flipping the flywheel by hand, check for spark on both spark plug wires.

Make sure that there is no interference between the flywheel and any part of the magneto, and the engine “flips’ easier if you leave the sparkplugs out.

If the spark appears to be good, install the flywheel nut and torque it down to the specs given in the factory service bulletin posted in the “Magnetos” column. After the nut is torqued, check for interference again.


If you do not know for a fact that the waterpump impeller is only one or two years old, I strongly suggest that you install a new one. I always do. Although many of the large old OMC engines have a little access panel on the motor “leg” that one can use to disconnect the shift linkage, the little 5 ½ does not have one. In order to change the water pump impeller, which is located in the lower unit, on the 5 ½, one must remove the power head first. The older engines, such as the ’55, are a bit easier to deal with because they do not have a “pan” under the power head, so the screws are a bit easier to get to, but it is not that big of a chore to remove the power head of any 5 ½. On the little Johnson, about 5 minutes had all the screws out and the power head ready to lift off, but I noticed that none of the screws was really “torqued-down” very tightly - it appeared that the power head had been removed in the not too distant past. To avoid having to disconnect the new fuel hose that I just installed, I unscrewed the fuel quick connect fitting from the engine, rather than disconnecting the hose from the fitting.

Before actually lifting the power head off of a 5 ½ (or an old 7 ½ for that matter), be aware that there is some “hardware” sitting on top of the driveshaft that you do not want to lose track of; have the outboard vertical (tilted all the way down) and carefully lift the power head off. Remaining on the driveshaft will be the seal for the lower end of the crankshaft, consisting of a ring resting on a pin driven through the driveshaft; a spring, and a seal thingy sitting on top, and there is another part or two in the mess. Carefully remove these pieces which are simply sitting on the driveshaft, and keep notes as to the order in which they are reinstalled.

With the power head off, you can now disconnect the shift linkage from the shift lever, and then unbolt and remove the lower unit.

Next time we will replace the pump impeller, and deal with a surprise problem.

Later

Max

 


Click images
to enlarge


carburetor parts


ready to work


going back together


installed on engine


magneto installed
& cam adjusted


points set


flywheel in place
spark check


flywheel nut torqued


powerhead screws


powerhead removed


driveshaft seal