Google

This time we have the following boats:

Send a picture or two and a short description of your boat and its launch
to chuck@duckworksmagazine.com for inclusion here next month.

PDR "Shredder"

Hey Chuck,

Here's a link to Andrew Linn's photoessay on the Puddle Duck Racer event last weekend. It included fotos of my new PDR, "Shredder", hull # 77, which was launched that day for the first time. I was still attaching hardware and figuring out the rigging until it was time to start the race. I got tangled up with someone milling about at the Start line, and got off to a very late start, but eventually made up a bit of ground and finished 4th. Not bad for a brand new boat, eh? I attribute much of that small bit of success to the OZ PDR influence... lug rig & rudder. It certainly wasn't the skipper!

I had the hull shell done way before Mik came out with the OZ PDR. Just hanging on my shop wall. When Andrew begged and bribed me with a sail, I finished it off with 82 sq. ft. balanced lug rig & rudder per Mik's spec. The leeboard is a clip-on of my own design... that converts to a rowing thwart. Just pull if up outa the water and flop it down on the seat risers. Voila'. My hull weighs maybe 45 pounds. It has a 3/8" bottom. The hollow square mast that Mik designed is amazingly light. Very nice.. They are a lot of fun. The performance came from two factors, I think: First, that's a lotta sail; Second, I think I did a fairly good job of keeping her flat with both transoms out of the water.

David Graybeal

Swampscott Dory

- funny how that works.
I should have known right away when I started to defrost frozen chicken
for supper.
I dropped it into the sink of warm water and went about the final little
things that in sure a highly successful first launch.
Later it defrosted to chicken broth.
Can't BBQ broth.

I was so excited.
Then I got a call from son number two, can't get away.
Wife has other commitments, just popped up.
I don't care. I'm going to the lake 7 miles, easy ramp, almost always
empty.
Everything went fine.
I backed in on the third try. And the boat floated off.
I had to quickly wade in to fetch it.
A kid held the rope and I parked a ways off.
Now there is no dock so wading in is just fine.
Settled in I rowed off from the ramp.
The boat, a 16 foot Swampscott Dory, looks great, rows straight and
true.
She is a little tender with the board up. And the tiller follows easily.
There is a little well where a cut down trolling motor just slides in.
The box needs to be a little higher. The water level is high.
When in place and turned on woooo the level gets even higher, splashing
over the top.
The box needs to be a little higher.
However the trolling motor does its job and the boat moves right along.
Shifting the movable ballast (me) helps but then reaching the tiller is
out.
I tie a line to the tiller and this is better, a whole lot less water
coming in.
Out in the lake I will put up the sails.
Well, reaching out over the bow to connect the forestay and jib need to
be changed.

The snotter/boom is all miss aligned and the main sail flops, on me.
There must be a leak somewhere, could be the centerboard pivot bolt.
When I was in the bow all the water moved to the front.
There is a substantial amount.
Now with the sails lines and boom all corrected what little wind
...disappeared.
I am in the lake about a mile, row?
Motor! Do your stuff
This is enough time and I have a list of modifications,
This place is now filling with happy boaters.
The wait is getting annoying.
The boaters are getting annoying.
Finally I get out and back on the trailer.
I forgot about a drain plug.
Bailing with a cut down soda bottle takes a half-hour.
I'm tired, hungry and finally am started home.

Don't you just hate it when things are going semi-badly and you hear
that sound telling you, pow, laugh, laugh, laugh.
That's the sound of a boat trailer wheel blowing its guts.
'I just had both those wheel checked'.
Tomorrow.
There's another day tomorrow.

GerryB

12-1/2' Kayak

Were you wondering what I did with the fiberglass and epoxy I ordered? Some of it went into this 12 1/2 foot kayak I built for my daughter. Splash date was Sept. 1, 2008.

I designed it based on the principles presented by Thomas Firth Jones in his book Boats to Go. What a thrill to see it floating, with daughter aboard, right where I planned, with the heel of the stem just clear of the water. In the photo, the stem looks higher out of the water because the water is so clear.

I built it with cedar strip bottom, fiberglass/epoxy inside and out, 5 mm luaun sides, and 3 mm sapele deck. I didn't get it weighed but she says it is light. The rub rail is vertical grain yellow pine cut from roof beams I salvaged from a school being remodeled. It's beautiful wood.

I call it a pond boat, not intended for any kind of rough water so no provision for a spray skirt. I also made the paddle, which she is holding upside down in the first photo.

Vince F.
Too Far North, Michigan

Kayak Tri "Three Amigos"

This was my solution for a light air/car topable cruiser for the summer winds in my area. I have a single and ketch rigged kayak but wanted more performance. I thought about building a hull and amas due to the more complicated spacing of hatches, masts, akas, and cockpits, but arthritic hands and the snails pace I painstakingly work at convinced me to find a finished boat. It's an 18' Seda hybrid double kayak I fitted with Balogh sails and 10 foot inflatable amas made up by a river rafting co. The 3 sails toal 106 sq.ft. It has 2 leeboards, and also has a 75 sq.ft Sailrite spinnaker I made but haven't finished rigging for this boat. The rudder, tiller, and it's connection parts I made as well as some other fittings.

Speeds are pretty good. 6-9 in 5-10+ MPH winds reaching, and it hit a max speed of 13.9 MPH on a broad reach in 15+ gusty conditions. I took a video showing the locations of all the control lines while sailing it (might post it on YouTube).
When the wind dies, I paddle 3mph with it fully rigged.

As kayaks go, storage is very good due to a large front cockpit/hatch and with it's volume provides a comparatively dry ride.

The boat is kevlar and weighs 55 lbs. Rigged it weighs 125. The cart I made has 16" Rolleez balloon wheels and I roll it fully rigged and loaded to the water.

This is probably more than you wanted to know but who doesn't like to talk about their own unique set-up!

I just wish there was a small boat Raid type event here in the NorthEast as I think my boat would be well suited for the adventure.

Hard to beat the beauty and conditions you have for the Texas 200. Makes me want to move South.

Brad

To comment on Duckworks articles, please visit our forum