Hawbuck (née Stripper Troutboat)  
Design by Larry Pullon - Little Rock, Arkansas - USA

As the project neared completion I had to rethink the name – “Troutboat” does not have the cache to match my feelings about this project. The more I thought the more “Hawbuck” kept coming back to the top of a short list. The name should reflect the character – and by golly nothing reflected that better than Hawbuck! In case you are wondering, I found the name on the net a few years ago while searching “old” words for something new. I found two sources for Hawbuck (or haw-buck) – one from New Zealand – meaning a clown or court jester, the other from USA, meaning a muleskinner (mule driver) – both uses are well outdated and very unlikely to be heard in either country.

click to enlarge

As the project neared completion I had to rethink the name – “Troutboat” does not have the cache to match my feelings about this project.

This boat was a funny thing with roots deep in the Ozarks. It was indeed the “Hawbuck” – so I ordered decals and vowed not to give it another thought. While I was at it I ordered “Miss Jenny” for the transom – trust me – putting your wife’s name on your boat is never a bad idea – it’s the thought that really counts!
.
This may be a recap, but the majority of the wood is cypress. I went to a sawmill near Batesville, AR and bought 5/4 cypress for $1.00 a board foot – well below the specialty wood store prices. The gunnels are ash, seat thwarts oak, painted bulkheads birch plywood, stained bulkheads oak plywood.

The gunnels are ash, seat thwarts oak, painted bulkheads birch plywood, stained bulkheads oak plywood.

click to enlarge

I found MinWax pecan stain to be a complementary color, adding to the natural richness of cypress, and covered it with several coats of satin finish spar varnish – the latter coats applied with a cotton cloth dipped in the varnish. It takes a couple of hours to varnish the whole thing with a paint brush – about 30 minutes with the cloth! There is a lot of wood to varnish on the Hawbuck – but I was still surprised when I had to go back to the store for more varnish!

click to enlarge

I like carpet in a boat – it is fun for your toes and it makes the hull quieter so you can sneak up on fish.

I like carpet in a boat – it is fun for your toes and it makes the hull quieter so you can sneak up on fish. I ordered ten feet of six feet wide (hunter green) bassboat carpet and split it right down the middle and glued it in the bottom of the hull. It looks inviting and is a real pleasure to walk on. The seats are Tempress seats from BassPro Shops – they run $100 each, which is a lot, but they so very comfortable the extra $$ was well spent.

Here is the boat’s namesake Miss Jenny expertly trying out the front seat for size.

click to enlarge

The bench tops and front deck is made of ½’x1” cypress strips. A good use for the two knotty boards I had left. Here is the boat’s namesake Miss Jenny expertly trying out the front seat for size.

The front seat may appear six inches too far forward – but actually it is there for a reason. The entire bow section is beefed up to act as a transom trolling motor mount – should I decide to use the boat for some backwater crappie or bass fishing. By placing the seat forward you can easily reach the trolling motor tiller handle. I have been known to sneak up on momma bass in these riverboats!

click to enlarge

The front seat may appear six inches too far forward – but actually it is there for a reason.

The last major task was fitting the giant stainless piano hinge that would hold the two hulls together. Fearing misalignment – I measured and made minute adjustments over and over for a ridiculous amount of time – and then finally said to heck with it and installed 64 - 2” stainless screws into the two hinge halves. Happily, the result was two properly aligned hulls!

The last major task was fitting the giant stainless piano hinge that would hold the two hulls together.

click to enlarge

On the LongJon I placed the hinge flat on top of the decks. It must have annoyed people because nearly every single person made a comment about the hinge. So this time I placed the hinge where only the edge would show when the boat was open. LongJon also had double bulkeads with 2”x 4”s in the middle on each side of the fold – I figured it was way overbuilt – so this time the bulkheads are one thickness of ¾” oak plywood – a risk maybe – but I think it will be plenty strong for protected waters. There are four 3”x 6” x 3/16” metal plates and two 5/8” stainless bolts to hold the hulls in the open position – just like I used with LonJon. With the bolts snugged down there was no hull movement between the hulls with the prototype – so I feel confident that two bolts are enough. I could not find stainless plate for a reasonable cost, so I used mild steel and painted them. Inside each bolt hole is a glued in copper tube – I learned on LongJon the wood holes swell making it hard to align the bolts.

click to enlarge

The bulkheads are one thickness of ¾” oak plywood – a risk maybe – but I think it will be plenty strong for protected waters.

Leak Tests!

The “Official Launch” will be at the Russellville messabout. But to me it is not reasonable to design and build a boat and then put it in the water the first time and expect everything to be ship shape. I nearly always forget something – mostly minor stuff – but hey, I am not by any means an engineer! What if the thing promptly folds up and sinks!!

It is not reasonable to design and build a boat and then put it in the water the first time and expect everything to be ship shape.

click to enlarge

So one week before the messabout Jenny and I headed to the Arkansas River for leak and safety tests – not to mention it had been a full year since I ran the 9.9hp Mercury. Wouldn’t you know- it rained! Oh! There is nothing more pitiful than to be waiting on the rain to launch a brand new boat! I check everything three times – paced, checked the weather channel, checked everything, paced – and generally got on Jenny’s nerves all morning!

click to enlarge

There is nothing more pitiful than to be waiting on the rain to launch a brand new boat!

Finally a break came in the weather and I quickly hooked up the trailer. Hawbuck sits on the trailer backwards – strange but very functional. This allows me to tow on a slightly modified trailer in the open or closed position. An interesting point about LongJon was the trailer collapsed – cool but a pain in the butt if you need to launch or recover in foul weather. Plus I had to remove the motor for transport – awe my aching back!

Hawbuck sits on the trailer backwards – strange but very functional. This allows me to tow on a slightly modified trailer in the open or closed position.

click to enlarge

So, Hawbuck sets on the trailer backward – motor always installed (it is bolted on). There is plenty of trailer bunk under the front section of the hull in the open position – allowing easy towing and fast launching.

Even though it was cloudy – the colors really came out once the boat was out of the shop! I know I should be modest and not be too fond of my own work – but I just love the wood tones and hunter green! It somehow makes me relax just looking at it.

click to enlarge

Jenny expertly manned the ropes and I eased down the ramp – secretly hoping she would float before water came over the bows.

We quickly drove 30 miles to the river – and before I could fully comprehend that months of planning and work and all the stuff that goes into boat making was about to come together we were setting on the boat ramp! This time I did remember one last photo!

Jenny expertly manned the ropes and I eased down the ramp – secretly hoping she would float before water came over the bows. My concern was wasted – this boat is very light and she came up very easy – not even close to taking on water. I also remembered to disconnect the tiedowns, raise the motor, AND install the drain plug!

This ‘99 Mercury has the water pick-up beneath the cavitation plate – you either have to run it in a bucket or buy an expensive adaptor.

click to enlarge

Lots of outboards have the water pickup down on the skeg. You can run them at home with “rabbit ears” and a water hose. This ‘99 Mercury has the water pick-up beneath the cavitation plate – you either have to run it in a bucket or buy an expensive adaptor. So after all the boat hoopla – I did not even know if the thing would start. I recalled I did run the carb dry the last outing – about thirteen months ago… Wouldn’t you know she started with the first pull and idled right down to a soft purr. Whew!

click to enlarge

Wouldn’t you know she started with the first pull and idled right down to a soft purr. Whew!

A few minutes later and we were boating! Jenny took her seat up front and I walked up and down the full length of the bottom. Not as stable as a 48” wide Jon boat – but the Hawbuck is very comfortable to walk around. I put one foot on the gunnels and pressed down – she remained level. The floor was just a little springy – there is only 3/8” of wood on the bottom (before sanding) and even with the strakes she gives a little when you walk, especially around the back section. I forgot, but you could “feel the water” with the plywood LongJon as well. I supposed it is common with large single layer bottoms.

A few minutes later and we were boating!

click to enlarge

Of course there were no leaks, not with two layers of 12oz glass on the outside and one on the inside. I assumed my position and soon we were underway. Thank goodness the motor did not cavitate! I literally guessed about the tunnel height and width and proper motor position. Too high and the prop will slip – to low and you wasted a lot of hours building a tunnel. Frankly, I don’t know if it could be better! Let’s just say you do not notice the boat has a tunnel – much less one that is offset a few inches.

click to enlarge

I tried various emergency maneuvers – hard turns, full stop from wide open – jerky stuff you would do to avoid a collision. My feet stayed dry and Jenny did not complain.

We went through a variety of stops, starts, turns, poking along, and wide open, everything you would do operating a boat. I tried various emergency maneuvers – hard turns, full stop from wide open – jerky stuff you would do to avoid a collision. My feet stayed dry and Jenny did not complain. I did notice the engine did not seem to run fast enough – then it dawned on me this was a 9.9 it runs 1000 rpm less than the 15hp motors I am accustomed to. I am using this motor because one of the rivers I want to visit has a 9.9 hp restriction. I guess it runs about 15 mph – maybe someone at the messabout will have a GPS and we will know for sure.

Here is the trailer – notice the bunks are angled to the right so the motor clears the winch.

click to enlarge

Anyway, Hawbuck has my stamp of approval. It is pretty, but it really is just a lowly fishing boat and will be used as such. In fact my bother and I will make a 75 mile camping/fishing trip in her – in a couple of weeks.

Notes: Here is the trailer – notice the bunks are angled to the right so the motor clears the winch. You have to tilt the motor up to trailer the boat. The only modification was the addition of longer bunks and the two metal supports up front.

This boat was built the old tyme “seat of the pants” way – simply put - my best guess. I am not by any means a qualified (or even novice) marine engineer so am oblivious if there are significant safety issues inherent in the design. I did not include design drawings, a bunch of numbers, etc, simply because the only drawings were a couple of sketches on the top of the work bench and are probably already under stains and whatnot. In fact as I sit here I already don’t recall much more than she is 18’ long and 54” at the beam (more or less). However, if someone wants to draw this up I will measure stuff for you – I only ask that you provide the “plans” free of charge to our fellow Duckworks readers.

click to enlarge
Click images for larger views 

You might want to know why Hawbuck folds. The answer is so it can be transported to and from the water on Tentboat’s deck. Look for 32’ Tentboat sometime in 2007!

Articles by Larry Pullon

SAILS

EPOXY

GEAR